A Cisco WLC has been added to the network and Cisco ISE as a network device, but authentication is failing. Which configuration within the network device configuration should be verified?

A. SNMP RO community

B. device interface credentials

C. device ID

D. shared secret

The Cisco Hyperlocation detection threshold is currently set to -50 dBm. After reviewing the wireless user location, discrepancies have been noticed. To improve the Cisco Hyperlocation accuracy, an engineer attempts to change the detection threshold to -100 dBm However, the Cisco Catalyst 9800 Series Wireless Controller does not allow this change to be applied. What actions should be taken to resolve this issue?

A. Place the APs to monitor mode shutdown the radios, and then change Cisco Hyperlocation detection threshold

B. Shutdown all radios on the controller, change the Cisco Hyperlocation detection range, and enable the radios again.

C. Disable Cisco Hyperlocation. change the Cisco Hyperlocation detection threshold and then enable it

D. Create a new profile on Cisco CMX with the new Cisco Hyperlocation detection range, and apply it on the WL AN.

A hospital wants to offer indoor directions to patient rooms utilizing its existing wireless infrastructure. The wireless network has been using location services specifications. Which two components must be installed to support this requirement? (Choose two.)

A. Cisco CMX Analytics

B. Cisco MSE

C. Cisco CMX AppEngage

D. WIPS

E. Cisco CMX Visitor Connect

ALLAR A network engineer must segregate all iPads on the guest WLAN to a separate VLAN.

How does the engineer accomplish this task without using Cisco ISE?

A. Enable RADIUS DHCP profiling on the WLAN.

B. Create a local policy on the WLC.

C. Use an mDNS profile for the iPad device.

D. Use 802.1x authentication to profile the devices

An engineer completes the setup of a wo-node Cisco ISE deployment for a guest portal. When testing the portal, the engineer notices that sometimes there is a certificate CN mismatch.

Which certificate type helps resolve this issue?

A. Public-Signed Root

B. Self-Signed Standard

C. Public-Signed SAN

D. Self-Signed Wildcard

A customer is concerned that their wireless network is detecting spurious threats from channels that are not being used by their wireless infrastructure. Which two technologies must they deploy? (Choose two.)

A. FlexConnect mode

B. monitor mode

C. sniffer mode with no submode

D. local mode with WIPS submode

E. rogue detector mode

A wireless engineer has performed a Wireshark ccapture on an 802.1x authentication process to troubleshoot a connectivity issue.

Which two types of packet does the EAP contain? (Choose two.)

A. EAP complete

B. EAP response

C. EAP failure

D. EAP request

E. EAP reply

An engineer has configured passive fallback mode for RADIUS with default timer settings. What will occur when the primary RADIUS fails then recovers?

A. RADIUS requests will be sent to the secondary RADIUS server until the secondary fails to respond.

B. The controller will immediately revert back after it receives a RADIUS probe from the primary server.

C. After the inactive time expires the controller will send RADIUS to the primary.

D. Once RADIUS probe messages determine the primary controller is active the controller will revert back to the primary RADIUS.

An engineer attempts to troubleshoot client connectivity issues in Cisco Prime Infrastructure. The Cisco Prime Infrastructure GUI is performing as expected, but the client detail information that is displayed is not current. The displayed client state and connected AP are up to 5 minutes old. Which action resolves this issue?

A. Change the data retention settings to 5 seconds.

B. Use a different browser to access the web interface.

C. Enable client Assoc/Disassoc and Auth/Deauth SNMP traps on the controller.

D. Optimize the Cisco Prime Infrastructure database.

DRAG DROP

The network management team in a large shopping center has detected numerous rogue APs from local coffee shops that are broadcasting SSIDs. All of these SSIDs have names starting with ATC (for example, ATC302, ATC011, and ATC566). A wireless network engineer must appropriately classify these SSIDs using the Rogue Rules feature. Drag and drop the options from the left onto the categories in which they must be used on the right. Not all options are used.

Select and Place: