Which of the following is Endpoint alarm?

A. Locked secure vault

B. Firewalled status

C. Network interface error

D. Temperature

E. Memory paging

When is it necessary to configure the SRDF Module rules? (Select 2)

A. Traffic originated between two EMC DMX arrays

B. Traffic originated from the Symmetrix FC ports (RF ports)

C. Traffic originated from the Symmetrix GigE ports (RE ports)

D. Traffic originated between two EMC V-Max arrays

For a new connection, a Load Balancing rule matches but none of the target Steelhead appliances in the rule are available. What will happen to the new connection?

A. The connection is passed through

B. The next rule in the list is examined

C. The Interceptor appliance triggers an alarm

D. The Interceptor appliance discontinues redirecting any new connections and places this rule in admissions control

Refer to the exhibit.

SH3 and SH4 are able to optimize HTTP sessions from Client41 to application host Server31. However, Client41 receives a failure messagE. "ftp connect: Unknown error number" while trying to connect Server32. The same applies to Client42. Note that SH3 and SH4 are in auto-discovery mode. Client41 and Client42 are able to ping Server32. What is the most likely cause of this failure?

A. The network interface card (NIC) at Server32 is down

B. The FTP service running in Server32 is down

C. An outbound access-list specified at R3f0 denies IP traffic from Client41 and Client42

D. An outbound access-list specified at R3f0 denies FTP control traffic from Client41 and Client42

E. The routing protocol between R3 and R4 is configured wrong

When deploying policy-based routing for multiple Steelhead appliances in a cluster, the router should be configured to: (Select 2)

A. Set IP next-hop address to the virtual IP address of the Steelhead appliance cluster

B. Set IP next-hop addresses for each Steelhead appliance

C. Check the state level information on each Steelhead appliance via SLA or CDP

D. Auto-detect the Steelhead appliance clustering protocol

E. Check the state level information on the virtual IP address of the Steelhead appliance cluster

What is the command to return a Steelhead appliance back to factory defaults?

A. (config) # restart factory reload

B. (config) # reload factory

C. (config) # restart clean

D. (config) # reload clean empty

E. (config) # reset factory reload

On an Interceptor appliance running Fair Peering v2, what Steelhead characteristic is used to calculate peer affinity?

A. Appliance size.

B. Percentage of data store free.

C. Maximum connection count.

D. Version of RiOS running.

-- Exhibit -- Exhibit -Refer to the exhibit. A Steelhead administrator has recently decided to implement two Interceptor appliances and one Steelhead appliance on his data center. After configuring the Interceptor and the Steelhead, he noticed the information on the screen when he logs into one of the Interceptor appliances. What does that represent? (Select 2)

A. This is normal ?it represents two Interceptor appliances in failover mode, with one Steelhead appliance in the cluster.

B. This is normal ?it represents two Interceptor appliances in parallel mode, with one Steelhead appliance in the cluster.

C. This is not normal ?the Steelhead appliance is showing none of 200 connections available.

D. This is normal ?the Steelhead appliance is showing there are 200 connections available.

You have just completed upgrading the software version on your SteelCentral Controller for SteelHead Mobile. What will happen to the software on the SteelHead Mobile clients?

A. The administrator must disconnect all clients and reinstall the software.

B. They will stop optimizing they have upgraded.

C. Nothing can happen until the administrator selects the new version in Manage > Assignments, Group Assignments.

D. They will be upgraded automatically when they next connect.

You have a client and server using SMB2 signing. You have SMB optimization enabled on your SteelHeads, but SMB signing is not enabled on the server-side SteelHead. What is the effect on this on an SMB connection which the SteelHeads attempt to optimize?

A. Any SMB2 connections between this client and server will be shown as optimized with protocol errors. No latency optimization or data reduction can be performed.

B. SMB2 connections between this client and server, which are initiated at the client side will be fully optimized with latency reduction.

C. Any SMB2 connections between this client and server will be optimized using data reduction only.

No latency optimization will take place.

D. Any SMB2 connections between this client and server will be optimized using latency optimization only No data reduction will take place.