Node 1 in a clustered pair detects that it has lost connectivity to one of its disk shelves. Node 1 is still up, but it cannot see one of its disk shelves. However, the partner node, Node 2, can see all of the Node 1's disk shelves. Which feature will cause Node 2 to monitor this error condition for a period of three minutes by default, and then forcibly take over Node 1 if the error condition persists?

A. Auto enable of giveback

B. Negotiated Fail Over

C. Takeover on panic

D. Cf.quickloop.enable

Using the output below, a co-worker determined that these are type "Solaris" LUNs. What would your determination be? lun show -m LUN pathMapped to LUN ID

/vol/vol1/lun0 solaris-igroup0 0 /vol/vol1/lun1 solaris-igroup1 0 /vol/vol1/qtree1/lun2 solaris-igroup2 0 /vol/vol1/qtree1/lun3 solaris-igroup3 0

A. These are type "Solaris" LUNs.

B. Not enough information is given here. Run the lun map command to get the information requested.

C. Not enough information is given here. Run the lun show -v command to get the information requested.

D. Not enough information is given here. Run the lun status command to get the information requested.

During an equipment move a Fibre Channel cable from a host to a switch is accidentally plugged into a different switch port on the FC switch. However, the host still sees the storage devices on all its paths. What are two reasons why this is possible? (Choose two.)

A. LUN masking uses switch port numbers and not WWPNs.

B. The host HBA WWPN is a part of a WWPN zoning scheme.

C. The Fibre Channel address for the HBA has not changed.

D. The WWPN Alias was n changed on the NetApp Controllers.

Which NetApp host utility command determines the number of paths per LUN visible to the host?

A. sanlun path show

B. sanlun lun show -p

C. sanlun fcp show adapter -p

D. sanlun fcp show adapter -c

A company has FC patch panels in their data center. They plan on using them to interconnect their storage controllers to the FC switches and the hosts using the storage. They have 62.5 micron cable between the patch panels. Which cable should you use on the NetApp storage controller's Target Ports to make this a supported configuration?

A. long wave SFPs, 62.5 micron FC cable

B. short wave SFPs, 50 micron FC cable

C. short wave SFPs, 62.5 micron FC cable

D. long wave SFPs, 50 micron FC cable

Which three statements are true about Asymmetric Logical Unit Access (ALUA)? (Choose three.)

A. It is a set of SCSI commands for discovering and managing multiple paths to LUNs on Fibre Channel and iSCSI SANs.

B. It requires Array Support Library (ASL), a proprietary vendor library.

C. It allows the initiator to query the target about path attributes, such as primary path and secondary path.

D. It no longer requires proprietary SCSI commands.

E. It works in standby and single_image cfmodes.

Which is a supported management switch?

A. Brocade 8000

B. Brocade FLS624

C. Cisco Nexus 5010

D. Cisco Nexus 7000

E. Cisco Catalyst 2960

F. Cisco Nexus 5020

Which command allows you to display the current zoning information for a Brocade switch?

A. switchshow

B. defzone --show

C. cfgshow

D. cfgzoneshow

Which type of VLAN protects against media access control (MAC) spoofing?

A. Static

B. Dynamic

C. NPIV

D. VSAN

An FC port on a NetApp storage system running clustered Data ONTAP is connected to an FC switch. FCP is licensed on the cluster and the Vserver FCP service is created and running. The state of the FC LIF, which is bound to the port, is

administratively up and operationally down.

What is the likely cause?

A. Improper FC zone configuration

B. NPIV is not enabled on the switch

C. Improper igroup configuration

D. Bad cable