Correct Answer: C

Explanation: One of the information that is communicated by bits in the PHY header is data rate. Data rate is the speed at which data is transmitted or received over the wireless medium. Data rate depends on factors such as modulation, coding, channel width, spatial streams, and guard interval. Data rate is indicated by bits in different fields of the PHY header, depending on the type of PPDU (e.g., OFDM, HT, VHT, HE). The receiver uses these bits to determine how to decode and demodulate the rest of the PPDU. The other options are not correct, as they are not communicated by bits in the PHY header. SNR (Signal-to-Noise Ratio), noise, and signal strengthare measured by the receiver based on its own capabilities and environment. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 101-105

Correct Answer: C

Explanation: The value of the Listen Interval field in an Association Request frame indicates how often a STA in power save mode wakes up to listen to Beacon frames. The Listen Interval is expressed in units of Beacon Intervals (typically 100 TU or 102.4 ms). For example, if the Listen Interval is set to 10, it means that the STA will wake up every 10 Beacon Intervals (or about 1 second) to check for buffered frames at the AP. The Listen Interval is used by the AP to determine how long it can hold frames for a STA in power save mode before discarding them . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 197; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 198.

Correct Answer: C

Explanation: A PHY header is added to the PSDU at the PHY layer. A PHY header is a part of the PPDU that contains information such as modulation, coding, and data rate. The PHY header is added by the PHY layer when it converts a PSDU to a PPDU for transmission, or removed by the PHY layer when it converts a PPDU to a PSDU for reception. The other layers do not add or remove a PHY header. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 97-98

Correct Answer: A

Explanation: The Swept Spectrogram plot is a spectrum analysis plot that shows the RF power present at a particular frequency over the course of time. It can help identify trends and patterns in the RF spectrum over a longer period of time. It can also show how the RF environment changes over time and how different sources of RF signals affect each other. The other options are not correct, as they describe different types of plots or information that are not related to the Swept Spectrogram plot. References: [Wireless Analysis Professional Study Guide], Chapter 3: Spectrum Analysis, page 72-73

Correct Answer: A

Explanation: An 802.11 wireless adaptor is required for Wi-Fi integration in laptop-based spectrum analyzer software in addition to the spectrum analysis adapter. The spectrum analysis adapter is a hardware device that captures the RF signals in the wireless environment and sends them to the spectrum analyzer software for analysis and display. The 802.11 wireless adapter is a hardware device that connects the laptop to the wireless network and allows the spectrum analyzer software to correlate the RF data with the Wi-Fi data, such as SSID, channel, and BSSID. This enables the spectrum analyzer software to provide more context and insight into the spectrum activity and its impact on the Wi-Fi network. A firmware upgrade for the spectrum analysis adapter is not required for Wi-Fi integration, but it may be needed to fix bugs or add features to the device. A directional antenna is an antenna that focuses the RF energy in a specific direction and has a high gain and a narrow beamwidth. A directional antenna can be used with a spectrum analysis adapter to pinpoint the location or source of interference or noise in the wireless environment, but it is not required for Wi-Fi integration. SNMP read credentials to the WLAN controller or APs are not required for Wi-Fi integration, but they may be useful for obtaining additional information about the wireless network configuration and performance from the network devices.References: CWAP-404 Study Guide, Chapter 4: Spectrum Analysis and Troubleshooting, page 123 CWAP-404 Objectives, Section 4.2: Integrate Wi-Fi data with spectrum analysis data CWAP-404 Study Guide, Chapter 4: Spectrum Analysis and Troubleshooting, page 131

Correct Answer: D

Explanation: The STA is discovering a list of available BSSs by sending a Probe Request with an empty SSID element. This is also known as a broadcast Probe Request, as it does not specify any particular SSID to probe for. Any AP that receives this Probe Request will respond with a Probe Response containing its own SSID and other information about its BSS. This way, the STA can learn about all the BSSs in its vicinity and choose which one to associate with . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 191; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter

6: MAC Sublayer Frame Exchanges, page 193.

Correct Answer: C

Explanation: The data rate at which the PHY preamble was transmitted is 6 Mbps. The PHY preamble is a part of the PPDU that is transmitted before the PHY header and the PSDU. The PHY preamble consists of a series of training fields that help the receiver to detect and synchronize with the signal. The PHY preamble is always transmitted at a fixed data rate that depends on the type of PPDU (e.g., OFDM, HT, VHT, HE). For an 802.1 lac data frame on channel 52, which uses VHT PPDUs, the data rate for the PHY preamble is 6 Mbps. This data rate does not depend on MCS (Modulation and Coding Scheme), which only affects the data rate for the PSDU. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 99-100

Correct Answer: D

Explanation: The most likely issue that can be identified from the spectrum analysis is a power mismatch between the APs and the clients. A power mismatch occurs when the APs transmit at a higher power level than the clients, or vice versa. This can cause asymmetric communication, where one side can hear the other, but not vice versa. This can result in poor performance, disconnections, or packet loss. A spectrum analysis can reveal a power mismatch by showing different signal amplitudes or RSSI values for the APs and the clients on the same channel or frequency. The other options are not correct, as they cannot be identified from the spectrum analysis alone. The tablets' SSID, power save mode,

and noise floor can be determined by using other tools or methods, such as protocol analysis, site survey, or device configuration. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 3: Spectrum Analysis, page

Correct Answer: D

Explanation: The GTK (Group Temporal Key) is encrypted within the third message of the 4-Way Handshake. The 4-Way Handshake is a process that establishes a secure connection between a STA (station) and an AP (access point) using WPA2 (Wi-Fi Protected Access 2), which is a security protocol that uses AES-CCMP (Advanced Encryption Standard-Counter Mode CBC-MAC Protocol) as its encryption algorithm. The 4- Way Handshake consists of four messages that are exchanged between the STA and the AP. The first message is sent by the AP to the STA, containing the ANonce (Authenticator Nonce), which is a random number generated by the AP. The second message is sent by the STA to the AP, containing the SNonce (Supplicant Nonce), which is a random number generated by the STA, and the MIC (Message Integrity Code), which is a value that verifies the integrity of the message. The third message is sent by the AP to the STA, containing the GTK, which is a key that is used to encrypt and decrypt multicast and broadcast data frames, and the MIC. The GTK is encrypted with the KEK (Key Encryption Key), which is derived from the PTK (Pairwise Temporal Key). The PTK is a key that is used to encrypt and decrypt unicast data frames, and it is derived from the PMK (Pairwise Master Key), the ANonce, and the SNonce. The fourth message is sent by the STA to the AP, containing only the MIC, to confirm the completion of the 4-Way Handshake. The other options are not correct, asthey are not encrypted within the third message of the 4-Way Handshake. The PMK is a key that is derived from a passphrase or obtained from an authentication server, and it is not transmitted in any message of the 4-Way Handshake. The PTK is a key that is derived from the PMK, the ANonce, and the SNonce, and it is not transmitted in any message of the 4-Way Handshake. The GMK (Group Master Key) is a key that is generated by the AP and used to derive the GTK, and it is not transmitted in any message of the 4-Way Handshake. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 8: Security Analysis, page 211-213

Correct Answer: A

Explanation: An RTS (Request to Send) frame should be acknowledged by a CTS (Clear to Send) frame. An RTS and CTS frame are types of control frames that are used to implement a virtual carrier sense mechanism called RTS/CTS. RTS/CTS is a technique that helps to avoid collisions and hidden node problems in wireless transmissions. When a STA (station) wants to send a data frame, it first sends an RTS frame to the intended receiver, indicating the duration of the transmission. The receiver then responds with a CTS frame, also indicating the duration of the transmission. The other STAs in the vicinity hear either the RTS or the CTS frame and update their NAV (Network Allocation Vector) timers accordingly, deferring their access to the medium until the transmission is over. The sender then sends the data frame, followed by an ACK (Acknowledgement) frame from the receiver. The other options are not correct, as they are not used to acknowledge an RTS frame. An ACK frame is used to acknowledge a data frame, not an RTS frame. An RTS- Ack frame does not exist, as there is no such type of control frame in 802.11. A Block Ack (BA) frame is used to acknowledge multiple data frames in a single frame, not an RTS frame. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 6:

802.11 Frame Exchanges, page 166-167