A technician receives a repurposed PowerEdge server. After racking and cabling the server, the technician attempts to log into the iDRAC but cannot do so. The default account has been disabled.

What method can be used to enable the default login account?

A. Run the racadm recreset command from the host OS.

B. Run the racadm recresetcfg command from the host OS.

C. SSH into the iDRAC and run the racadm racresetcfg command.

D. SSH into the iDRAC and run the racadm racreset command.

A technician needs to add a device to SupportAssist Enterprise. Policy requires that no additional software be installed on the server OS.

In addition to Username and Password, what information is required to add the device?

A. IP address or hostname for the server OS

B. IP address for Dell TechDirect

C. IP address fir OpenManage Server Administrator

D. IP address or hostname for the iDRAC

Eight new servers have arrived at a datacenter. All use static IP addresses for iDRAC. The technician needs to enable these servers to contact the DHCP server on the network to obtain new IP addresses.

What method can the technician use to quickly switch to DHCP?

A. Reboot each server to enable DHCP default settings

B. Boot into CTRL+S and change iDRAC settings to DHCP

C. Use the LCD panel to input a new IP address

D. Log in to the iDRAC and enable DHCP

A technician is working on an operational PowerEdge R640 server that cannot be rebooted. Observing that all drives are hot-swappable devices, the technician decides to remove a drive that has been giving intermittent errors. After the single drive is removed the operating system crashes.

What could have caused the operating system to crash?

A. System Lockdown mode was enabled, which does not allow any component to be hot-swapped

B. iDRAC was not configured for hot-swappable components

C. Drive was part of a RAID 0 virtual disk

D. PERC was configured to allow a single drive removal

A technician is changing the iDRAC IP address from the static IP address 10.37.125.88 to DHCP on the technician's PowerEdge R640 that does not have a front LCD. After completing this task, they are unable to determine which IP address was given to the iDRAC and they cannot reboot the server.

What method could the technician use to determine that IP address is assigned to the iDRAC?

A. Use the iDRAC Direct feature. Access iDRAC web GUI and determine the assigned IP address

B. Plug a monitor or KVM into the system. Reboot the server to view the assigned IP iDRAC address on the Dell boot up splash screen

C. Log in to the Lifecycle and check the iDRAC Settings.

D. Hold the system identification button down for more than 3 seconds to reset it back to the default static address 192.168.0.120

A technician needs to deploy a server into production and needs to verify that the firmware levels match corporate policy before putting the server on the business network.

Which method is recommended for verifying the firmware version of iDRAC and BIOS?

A. Scroll through the menus on the LCD panel to view the BIOS and iDRAC firmware levels

B. SSH into the iDRAC and run the racadm systemconfig command to view current firmware

C. Use the Lifecycle Controller and navigate to Firmware Update to view current versions

D. Use the OMSA DVD that came with the server to view Current Drivers and Firmware

A technician must update the firmware on a server, but has no network connectivity. What can the technician use to update the BIOS and iDRAC/Lifecycle Controller firmware?

A. OpenManage Server Administrator DVD

B. ftp.dell.com

C. NFS share

D. USB key with Dell Update Package

Refer to the exhibit.

A technician tries to apply a BIOS update on a server through the iDRAC web interface using the Linux Dell Update Package file BIOS_2H4CC_LN_2.0.2.BIN. This results in the error shown in the exhibit.

What should the technician do to address this issue?

A. Reset the iDRAC and reapply the update

B. Extract the Linux Dell Update Package and apply payload file

C. Re-download the file to replace the corrupted version and reinstall

D. Download and apply the Windows Dell Update Package file

A technician needs to initially configure a server from a bare metal condition in the following area. Processor settings Disk configuration iDRAC network settings

The technician can only reboot the server once to achieve these tasks.

Where should the technician configure these settings?

A. PERC Configuration Utility and iDRAC Settings

B. PERC Configuration Utility only

C. System BIOS, iDRAC Settings, Device Settings

D. Device and PXE Settings

A technician needs to use the iDRAC GUI to roll back a diagnostics firmware revision on a server that was updated four weeks previously. However, the replaced version cannot be found in the Firmware Rollback section on the iDRAC GUI.

What could be the issue?

A. Diagnostics firmware revision is part of the Lifecycle Controller firmware so the Lifecycle Controller must be updated first

B. Rollback feature was not enabled in iDRAC Settings

C. Firmware can only be rolled back within a week of being replaced.

D. Diagnostics firmware is not supported in the Rollback feature.