You have completed a clustered Data ONTAP installation for a new customer. You are now ready to hand off the system to the customer.

Which three actions should you take at this stage in the installation process? (Choose three.)

A. Show the customer how to open a case with NetApp Support.

B. Demonstrate System Manager and its functionality.

C. Tell the customer to call their sales representative if there are further questions.

D. Tell the customer you are finished and then leave the site.

E. Show the customer how to set up a support account.

Regarding clustered Data ONTAP 8.3, what happens to the roles of the on board ports, HBAs, and NICs?

A. These roles are assignet when LIFs are created.

B. These roles are assigned based on the controller type.

C. These roles are predefined and must be changed before creating your LIFs.

D. The roles are divided into two categories: Data Management and Node Management.

You are adding nodes to an existing cluster.

In this scenario, which three statements are correct? (Choose three.)

A. If you are adding a second node to a single-node cluster, the second node must have been installed, but the cluster network can be configured later.

B. You must add a cluster switch for every two nodes.

C. If you are adding nodes to a multiple-node cluster, more than half of the existing nodes in the cluster must be healthy.

D. The switchless cluster functionality is supported only in a single or two-node cluster.

E. If you are adding nodes to a two-node switchless cluster, you must have installed and configured the cluster management and interconnect switches before adding additional nodes.

What is a protocol?

A. SnapRestore

B. CIFS

C. SnapMirror/SnapVault

D. FlexClone

A customer is installing a new system. The administrator needs to have the maximum available amount of data space.

Which disk configuration should the administrator use?

A. RAID-DP

B. RAID4

C. Flash Pool

D. ADP

A customer is installing a new system and has determined that they have a broken disk.

What information is required to open a NetApp Support case?

A. disk HBA firmware and serial number

B. mainboard rev. id

C. serial number or system ID

D. disk shelf serial number and shelf ID number

You are asked to install a 6-node cluster of FAS8080 controllers. The installation has been completed and Config Advisor shows no warnings or errors. The customer can ping and access the controller.

Which statement is true in this scenario?

A. This installation has not been completed successfully until you have confirmed that SSH is enabled.

B. This installation has not been completed successfully until the customer and NetApp Support have received a minimum of three AutoSupport messages.

C. This installation has been completed successfully only if you have confirmed that the configuration is correct.

D. This installation has been completed successfully, because Config Advisor would identify the missing configuration.

You are planning to install a new clustered Data ONTAP system for a customer.

Which action should be performed before configuring the cluster network switches?

A. Confirm IP address and configuration information for Brocade switches before configuring the switches.

B. Use the Cluster Network and Management Network Compatibility Matrix URL before configuring the switches.

C. Use the Inventory Collect Tool before configuring the switches.

D. Download the Fibre Channel switches software before configuring the switches.

Click the Exhibit button.

You are asked to install a new cluster with six FAS8060 nodes. While running Config Advisor, you see the messages shown in the exhibit. The customer does not want ACP cabled on their cluster.

Which two actions would allow the installation to be completed successfully? (Choose two.)

A. Advise NGS that the customer has a controller in an unsupported state.

B. Advise the customer that they must acknowledge that they are not using ACP on the installation.

C. Advise the sales team that the customer is operating without ACP and that the customer is asking you to leave it that way.

D. Advise the customer that the error will cause the controller to not operate properly and create an unsupported state.

You want to install a new clustered Data ONTAP 8.3 system. The customer wants to use open ports on interconnect switches from a different system with clustered Data ONTAP 8.2 because they are running out of space in their rack.

What should be considered in this scenario?

A. Only one cluster per switch pair is qualified and supported.

B. You can use all free network ports for the cluster interconnect.

C. You can only use dedicated ports for the clustered interconnect.

D. A maximum of two clusters per switch pair are qualified and supported, but you should use trunked ports.