You are trying to deploy a Connector in the AWScloud from NetApp Cloud Manager. The deployment fails and shows the message 'Insufficient permissions to deploy Cloud Connector". You have verified the AWS access key and the AWS secret key.

In this scenario, what Is the reason that the deployment failed?

A. No AWS Marketplace subscription is associated with Cloud Manager.

B. The required Identity and Access Management (IAM) policies were not Installed.

C. The user lacks the permission to deploy within Cloud Manager.

D. The Connector can be deployed only inAWS GovCloud (US).

You receive the "Unable to connect to the management gateway server"error when trying to connect to a node management IP.

In this situation, how do you determine whether core dumps are generated for the mgwd user space process?

A. Log in to the nodeshell using the node console and collect the core dumps from the nodeshell.

B. Log in to the service processor and collect the core dumps from the service processor.

C. Log in to the clustershell using the node console and collect the core dumps from the clustershell.

D. Log in to the systemshell and collect core dumps from thesystemshell.

An administrator receives the following error message:

What are two causes for this error? (Choose two.)

A. There Is excessive SSD load causing the wear leveling to become unbalanced.

B. A disk is falling.

C. There is excessive SATA HDD load.

D. An SSD disk is performing garbage collection to create a dense data layout.

You notice poor performance on your FlexGroup and execute the system node run -node * flexgroup show command for more Information. You notice the "Urge" column has non-zero values.

In this scenario, which statement is true?

A. The aggregate is completely full.

B. The constituent volumes are out ofInodes.

C. The data placement is uneven.

D. The constituent volumes are completely full.

Your customer installed the shelf firmware for their NS224 shelf over a week ago, and the firmware has notupgraded on shelf 1 module B. The customer wants to know what the next steps would be to get the firmware upgraded after verifying that the shelf firmware is indeed loaded onto the system.

Which step would you perform to complete the firmware upgrade?

A. Reseat the NSM100 module.

B. Reseat the disk in Bay 0.

C. Power cycle the shelf.

D. Reseat the PSU of the shelf.

Your customer noticed in NetApp Active IQ that their NetApp Cloud Volumes ONTAP forAzure HA solution is no longer sending AutoSupport messages over HTTPS. A support ticket has been opened to find out why. No changes have been made to the Cloud Volumes ONTAP for Azure HA environment.

In this scenario, which two autosupport command parameters should be used to validate that AutoSupport Is working properly? {Choose two.)

A. -mail-hosts

B. -transport

C. -proxy-url

D. -to

Referring to the exhibit, from which delay center is most of the latency for voll?

A. Disk

B. Network

C. Data

D. NVRAM

Your customer is running a NetApp AFF A800 system with NetAppONTAP 9.8 software and states that their NS224 shelf is not showing with the correct shelf ID. You analyze the data and the shelf shows an identification of "1.SHFHUXXXXXXXXXX."

What is the cause of the reported Issue?

A. The shelf has been power cycled.

B. A new shelf was added to the controller.

C. The shelf had a disk replaced too quickly.

D. The shelf was cabled Incorrectly.

You ate connecting a Windows Server 2019 hostto ISCSI LUNs on a 4-node AFF A250 cluster running NetApp ONIAP 9.8 software. The host is unable to connect to the target interface, and the ONTAP event log has the message shown

below.

ISCSI: network interface identifier disabled for use; incoming connection discarded

In this scenario, what is the cause of this connection issue?

A. iSNS is not enabled on the storage virtual machine.

B. The WWPN was not added to the initiator group.

C. The iSCSI service is not enabled on the interface.

D. CHAP isnot configured correctly for the specified initiator.

You created a new NetApp ONTAP FlexGroup volume spanning six nodes and 12 aggregates with a total size of 4 TB. You added millions of files to the FlexGroup volume with a flat directory structure totaling 2 TB, and you receive anout of apace error message on your host.

What would cause this error?

A. The maximum number of volume constituents has been reached in the ONTAP software.

B. All constituent volumes are full.

C. The inode limit is exceeded in the ONTAP software.

D. The maxdirsize Is exceeded in the ONTAP software.