Which supported step should an administrator perform to ensure all operating system logs are sent from an appliance to a central logging server running Linux?

A. configure access to the appliance logs with the share open command

B. configure syslog forwarding in the appliance CLISH

C. configure syslog forwarding in OpsCenter

D. configure a cron job on the appliance to copy the logs

Refer to the exhibit.

Two media servers, sharing a library with 6 tape drives, exist in the NetBackup environment displayed in the exhibit. Both weekly Full and daily Differential Incremental backups need to run for the clients and each schedule has a different retention period. Because of network topology, some clients back up to Media server 1 and some back up to Media server 2. The environment suffers from multiple status 96 failures during the backup window.

How can the administrator minimize the number of failures?

A. increase the "Media unmount delay"

B. configure media multiplexing

C. enable backups to span tape media

D. enable media sharing

Prior to initiating a restore, an administrator realizes that media needed for the restore was written by a server that is unavailable. The administrator does have another server that can perform the restore and that is connected to the same library.

Which two commands can the administrator perform to change the server ownership, so the restore can be performed? (Choose two.)

A. bpimage

B. bpimmedia

C. bpimagelist

D. bpmedia

E. bpimport

An administrator is experiencing a backup failure, which may be due to lack of connection between the

media and master server. The status of the media server is shown below:

Media server showing offline

Which command can the administrator run to change the status of the media server?

A. bptestbpcd

B. nbdb_admin

C. nbemmcmd

D. bpminlicense

An administrator has configured a Storage Lifecycle Policy (SLP) to protect a large number of clients which directs backups to Advanced Disk, then duplicates the images to tape. The administrator is experiencing an SLP backlog, which is causing backups to fail. The current values of key configuration settings are listed below:

Host Properties - Maximum data streams per client = 1 Policy Settings - Maximum jobs per policy = 20 Disk Pool Settings - Maximum I/O streams = 20 Storage Unit Settings - Maximum concurrent jobs = 20 Storage Unit Settings - Multiplexing level = 20

Which parameter should the administrator change to reduce the SLP backlog and allow the backups to complete successfully?

A. Increase Maximum data streams per client

B. Increase Maximum jobs per policy

C. Increase Maximum I/O streams for the disk pool

D. Increase Maximum concurrent jobs for the storage unit

A NetBackup master server has commenced writing four long-running duplication jobs to an AdvancedDisk disk pool. The value of "Maximum concurrent jobs" for the storage unit and "Limit I/O streams" for the disk pool are both set to 4.

There are 35 jobs queued on the master server that require this disk pool: 5 replication jobs with priority 9999 10 backup jobs with priority 999 20 duplication jobs with priority 99

Two restore jobs that require this disk pool are then submitted with default priority. Which job type goes active next?

A. Backup

B. Duplication

C. Replication

D. Restore

An administrator has a backup policy with the following policy attributes:

3 paths listed in the Backup Selections list 5 clients listed in the Clients list "Allow multiple data streams" is selected "Limit jobs per policy" is set to 4

How many jobs go Active when the job is started, excluding parent jobs, assuming there are enough storage resources to handle the expected jobs?

A. 3

B. 4

C. 12

D. 15

How can an administrator view the bpbrm log files on an appliance using the NetBackup Appliance Shell Menu (CLISH) interface?

A. Support > Logs > Share

B. Support > Logs > Browse

C. Support > Logs > Upload

D. Support > Logs > VxLogView

Which communication protocol and port does the Appliance Management Server use to communicate with Appliance Management agents?

A. https (443)

B. http (80)

C. https (8443)

D. http (8080)

An administrator is configuring a new device and receives the following error message:

Unable to determine robot type

What are two possible solutions? (Choose two.)

A. download a new device_mapping file from the Veritas Support website

B. ensure the tape drive is closed and ready for use

C. perform a rescan of the available tape drives

D. verify compatibility for the library with NetBackup

E. select the correct device type for the drives