Your new customer is concerned about maintaining privacy for their proprietary information when you conduct information gathering for their WLAN design. Which document can you use to directly address their concern?

A. NDA

B. SoW

C. BoM

D. Hold Harmless

You're about to deploy an Enterprise-class VoWLAN infrastructure. You need to ensure that QoS is properly configured throughout the network. What Access Category (AC) should voice frames/packets use?

A. AC_VI

B. AC_VO

C. AC_BE

D. AC_BK

After importing a floor plan to a predictive design tool, what should be done prior to adding APs, antennas and attenuators (e.g., walls)?

A. Set the transmit power for all APs

B. Add pictures of the environment

C. Nothing; just begin by adding APs, antenna and attenuators

D. Calibrate the floor plan to increase accuracy

When designing a static channel plan for an office using voice devices near an airport, which range of channels should be avoided to ensure optimal performance when implemented?

A. 36-40

B. 44-48

C. 116-124

D. 1-11

After designing a WLAN infrastructure using predictive design software. What's the best way to validate the predictive design in the physical space before deployment, if time and budget allow for it?

A. Deploy all of the APs as they're shown in the predictive design and perform an active site survey.

B. Deploy all of the APs as they're shown in the predictive design and perform a passive site survey.

C. Use a client device positioned where the APs will be installed and measure the signal from the client device.

D. Perform an AP-on-a-Stick survey using AP locations based upon the predictive design to confirm each AP's placement.

Your customer requires fast secure roaming. Which two types of roaming are specified in 802.11-2016 FT roaming that will help meet this goal?

A. Over-the-Air and Over-the-DS

B. Over-the-Air and Over-the-Wire

C. FT and OKC

D. FT and TKIP

What document should be created that provides instructions for install technicians to mount and configure APs?

A. Hold Harmless

B. Statement of Work

C. Bill of Materials

D. Physical installation guide

During lunch time in the break room of a company, Wi-Fi connectivity on the 2.4 GHz band is intermittent. Every other time of the day, it works fine. What's the likely cause of this issue?

A. Employees are using their cell data instead of using the Wi-Fi

B. The AP in the cafeteria keeps rebooting due to lack of PoE budget on the switch

C. Toasters and ovens are heating up the air, raising the noise floor with the Wi-Fi on the 2.4 Ghz band

D. Microwaves in the cafeteria are interfering with the Wi-Fi on the 2.4 GHz band

After designing and deploying a WLAN infrastructure, you realized the CCI is causing poor performance in the 2.4 GHz band. Primarily, you've designed the WLAN for 5 GHz and 2.4 GHz as a best effort. You found out that the implementers didn't follow your guidelines when configuring the WLAN infrastructure.

What can you do to minimize as much as possible the CCI impact in the 2.4 GHz band?

A. Add more APs to the infrastructure

B. Increase the transmit power on all APs

C. Turn-off 2.4 GHz radios on some APs

D. Use all channels available in the 2.4 GHz band

In a convention center, you have received complaints about the WLAN infrastructure. At this moment, the are only two APs in one auditorium. After analyzing the situation, you determined that there are more client devices that the infrastructure was designed for. There are only two APs to support more than 300 devices using the Wi-Fi at the same time. What should you do to make the Wi-Fi work as expected?

A. Redesign the entire WLAN

B. Quickly add more APs

C. Upgrade the Ethernet connections to MultiGig

D. Turn up the output power on the APs so that they can handle more clients